//******************************************************************************************
//  PIC12F1822 Sample Program
//   Project      :
//   Program Name :
//   Programer    :
//   Create date  :  
//   History      :
//   Laungage     :  HI_TECH PICC C Laungage Version 9.83
//******************************************************************************************
//   Description
//******************************************************************************************
#include	<htc.h>
__CONFIG(  FOSC_INTOSC & WDTE_OFF & PWRTE_OFF &  MCLRE_OFF & CP_OFF & CPD_OFF 
                       & BOREN_OFF & CLKOUTEN_OFF & IESO_OFF & FCMEN_OFF );
__CONFIG(  WRT_OFF & PLLEN_OFF & STVREN_OFF & BORV_HI & LVP_OFF ) ;
//

void Wait_01S(unsigned int);
void Wait_100mS(void);

void main()
{

// *****************************
//   1.Initialized 
// *****************************
// (1)Define OSC (16MHz, IntOSC)
    OSCCON = 0b01111010;    // 16MHz,    IntOSC

// (2)Define ANSELA (ALL Digital Port)
    ANSELA = 0x00;

// (3)Define I/O port
    PORTA  = 0b00000000;
    TRISA  = 0b00111000;

// *****************************
//   2.Program main
// *****************************
    while(1){
        PORTA = 0b00000000;
        Wait_01S((unsigned int)10);
        PORTA = 0b00000111;
        Wait_01S((unsigned int)10);
    };
}

//******************************************************************************************
//   Function Name : Wait_01S
//   Title         : This function will wait n times of 0.1 seconds
//   Input         : 
//   Output        :
//******************************************************************************************
void Wait_01S(unsigned int n)
{
    unsigned int lp;

    for(lp=0;lp<n;lp++){
        Wait_100mS();
    } 
}

//******************************************************************************************
//   Function Name : Wait_100mS
//   Title         : This function will wait 100 mS
//   Input         : 
//   Output        :
//******************************************************************************************
void Wait_100mS(void)
{
// *******************************************************
// 1.Define T1CON(TIMER1 CONTROL REGISTER) Register
//   T1CON(7-6)  TMR1CS1,TMR1CS0: Timer1 Clock Source Select bits
//                  11 =Timer1 clock source is Capacitive Sensing Oscillator (CAPOSC)
//                  10 =Timer1 clock source is pin or oscillator:
//                    If T1OSCEN = 0:   External clock from T1CKI pin (on the rising edge)
//                    If T1OSCEN = 1:   Crystal oscillator on T1OSI/T1OSO pins
//                  01 =Timer1 clock source is system clock (FOSC)
//                  00 =Timer1 clock source is instruction clock (FOSC/4)
//   T1CON(5-4)  T1CKPS1,T1CKPS0:  Timer1 Input Clock Prescale Select bits
//                  11 = 1:8 Prescale value
//                  10 = 1:4 Prescale value
//                  01 = 1:2 Prescale value
//                  00 = 1:1 Prescale value
//   T1CON(3)    T1OSCEN: LP Oscillator Enable Control bit
//                  1 = Dedicated Timer1 oscillator circuit enabled
//                  0 = Dedicated Timer1 oscillator circuit disabled
//   T1CON(2)    T1SYNC: Timer1 External Clock Input Synchronization Control bit
//                  TMR1CS1,TMR1CS0  = 1X
//                     1 = Do not synchronize external clock input
//                     0 = Synchronize external clock input with system clock (FOSC)
//                  TMR1CS1,TMR1CS0  = 0X
//                     This bit is ignored. Timer1 uses the internal clock when TMR1CS<1:0> = 1X.
//   T1CON(1)    Unimplemented: Read as �e0�f
//   T1CON(0)    TMR1ON: Timer1 On bit
//                  1 = Enables Timer1
//                  0 = Stops Timer1
//                      Clears Timer1 Gate flip-flop
// *******************************************************
    T1CON = 0b00110001;

// *******************************************************
// 2.Define T1GCON (TIMER1 GATE CONTROL REGISTER) Register
//   T1GCON(7) TMR1GE: Timer1 Gate Enable bit
//       If TMR1ON = 0:
//           This bit is ignored
//       If TMR1ON = 1:
//           1 = Timer1 counting is controlled by the Timer1 gate function
//           0 = Timer1 counts regardless of Timer1 gate function
//   T1GCON(6) T1GPOL: Timer1 Gate Polarity bit
//       1 = Timer1 gate is active-high (Timer1 counts when gate is high)
//       0 = Timer1 gate is active-low (Timer1 counts when gate is low)
//   T1GCON(5) T1GTM: Timer1 Gate Toggle Mode bit
//       1 = Timer1 Gate Toggle mode is enabled
//       0 = Timer1 Gate Toggle mode is disabled and toggle flip-flop is cleared
//           Timer1 gate flip-flop toggles on every rising edge.
//   T1GCON(4) T1GSPM: Timer1 Gate Single-Pulse Mode bit
//       1 = Timer1 gate Single-Pulse mode is enabled and is controlling Timer1 gate
//       0 = Timer1 gate Single-Pulse mode is disabled
//   T1GCON(3) T1GGO/DONE: Timer1 Gate Single-Pulse Acquisition Status bit
//       1 = Timer1 gate single-pulse acquisition is ready, waiting for an edge
//       0 = Timer1 gate single-pulse acquisition has completed or has not been started
//           This bit is automatically cleared when T1GSPM is cleared.
//   T1GCON(2) T1GVAL: Timer1 Gate Current State bit
//      Indicates the current state of the Timer1 gate that could be provided to TMR1H:TMR1L.
//      Unaffected by Timer1 Gate Enable (TMR1GE).
//   T1GCON(1-0) T1GSS1,T1GSS0: Timer1 Gate Source Select bits
//      00 = Timer1 Gate pin
//      01 = Timer0 overflow output
//      10 = Comparator 1 optionally synchronized output (SYNCC1OUT)
//      11 = Comparator 2 optionally synchronized output (SYNCC2OUT)
// *******************************************************
    T1GCON = 0b00000000;

// *******************************************************
// 3.Define TMR1 Register
// *******************************************************
//   TMR1 data ( OSC:16MHz, FOSC/4, 1:8 Prescale value, 0.01[S];100Hz )
//     10mS(100Hz): 16MHz / 4(FOSC/4) / 8(Prescale) / 100(100Hz)==> 0d5,000(Count)  ==> 0x1388(Count)
//     TMR1 = 0xFFFF - 0x1388 ==> 0xEC77
//   TMR1 data ( OSC:16MHz, FOSC/4, 1:8 Prescale value, 0.1[S];10Hz )
//     100mS(10Hz): 16MHz / 4(FOSC/4) / 8(Prescale) / 10(10Hz)  ==> 0d50,000(Count) ==> 0xC350(Count)
//     TMR1 = 0xFFFF - 0xC350 ==> 0x3CAF
    TMR1H = 0x3C;
    TMR1L = 0xAF;

// *******************************************************
// 4.Check Timer1
//      PIR1: PERIPHERAL INTERRUPT REQUEST REGISTER 1
//         PIR1[7] TMR1GIF: Timer1 Gate Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[6] ADIF: A/D Converter Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[5] RCIF: USART Receive Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[4] TXIF: USART Transmit Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[3] SSP1IF: Synchronous Serial Port (MSSP) Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[2] CCP1IF: CCP1 Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[1] TMR2IF: Timer2 to PR2 Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
//         PIR1[0] TMR1IF: Timer1 Overflow Interrupt Flag bit
//              1 = Interrupt is pending  /  0 = Interrupt is not pending
// *******************************************************
//  (1)Clear the TMR1IF Flag bit
    PIR1 &= 0b11111110;

//  (2)Check the TMR1IF Flag bit
    while((PIR1 &= 0b00000001) == 0 );

}