/***********************************************************************************************************************
* DISCLAIMER
* This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products.
* No other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all
* applicable laws, including copyright laws. 
* THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING THIS SOFTWARE, WHETHER EXPRESS, IMPLIED
* OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NON-INFRINGEMENT.  ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED.TO THE MAXIMUM EXTENT PERMITTED NOT PROHIBITED BY
* LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES SHALL BE LIABLE FOR ANY DIRECT,
* INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS SOFTWARE, EVEN IF RENESAS OR
* ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
* Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability 
* of this software. By using this software, you agree to the additional terms and conditions found by accessing the 
* following link:
* http://www.renesas.com/disclaimer
*
* Copyright (C) 2011, 2018 Renesas Electronics Corporation. All rights reserved.
***********************************************************************************************************************/

/***********************************************************************************************************************
* File Name    : r_main.c
* Version      : CodeGenerator for RL78/G14 V2.05.02.05 [30 May 2018]
* Device(s)    : R5F104PJ
* Tool-Chain   : CCRL
* Description  : This file implements main function.
* Creation Date: 2018/11/01
***********************************************************************************************************************/

/***********************************************************************************************************************
Includes
***********************************************************************************************************************/
#include "r_cg_macrodriver.h"
#include "r_cg_cgc.h"
#include "r_cg_serial.h"
/* Start user code for include. Do not edit comment generated here */
/* End user code. Do not edit comment generated here */
#include "r_cg_userdefine.h"

/***********************************************************************************************************************
Pragma directive
***********************************************************************************************************************/
/* Start user code for pragma. Do not edit comment generated here */
/* End user code. Do not edit comment generated here */

/***********************************************************************************************************************
Global variables and functions
***********************************************************************************************************************/
/* Start user code for global. Do not edit comment generated here */
/* End user code. Do not edit comment generated here */
void R_MAIN_UserInit(void);

/***********************************************************************************************************************
* Function Name: main
* Description  : This function implements main function.
* Arguments    : None
* Return Value : None
***********************************************************************************************************************/
void put_message(uint8_t *);
void main(void)
{
    uint8_t rtx_buf = 0x00;
	
    R_MAIN_UserInit();
    
    R_UART1_Start();

    put_message((uint8_t  *)"RL78/G13 (Tx1) Connected OK >");
    
    /* Start user code. Do not edit comment generated here */
    while (1U)
    {

        while((SSR03 & 0x0040)== 0){        //Check TSF03 (Recive) SSRmn(m:unit number[0,1]/n:channel number[0,1,2,3])
            R_UART1_Receive(&rtx_buf,(uint16_t)1); 
        }     
        while((SSR03 & 0x0040)!= 0);        //Check TSF03 (Recive) SSRmn(m:unit number[0,1]/n:channel number[0,1,2,3])

        while((SSR02 & 0x0040)!= 0);        //Check TSF02 (Send)   SSRmn(m:unit number[0,1]/n:channel number[0,1,2,3])
	R_UART1_Send(&rtx_buf,(uint16_t)1);
       
    }
    /* End user code. Do not edit comment generated here */
}
void put_message(uint8_t  *message)
{    
    while(*message != 0x00){        
        while((SSR02 & 0x0040)!= 0);         //Check TSF02 (Send)  SSRmn(m:unit number[0,1]/n:channel number[0,1,2,3])
        R_UART1_Send((uint8_t  *)message,(uint16_t)1);
        message++;
    }	    
}
/***********************************************************************************************************************
* Function Name: R_MAIN_UserInit
* Description  : This function adds user code before implementing main function.
* Arguments    : None
* Return Value : None
***********************************************************************************************************************/
void R_MAIN_UserInit(void)
{
    /* Start user code. Do not edit comment generated here */
    EI();
    /* End user code. Do not edit comment generated here */
}

/* Start user code for adding. Do not edit comment generated here */
/* End user code. Do not edit comment generated here */